Mattig 200p ac dc manual

TIG201 AC/DC INVERTER . TIG WELDER . OPERATION INSTRUCTIONS. Version 2014-1. 2 . 3 Please read all information in this manual before operation . This switch selects either DC for welding steels or AC for welding alloys Technical data MATTIG 200P AC/DC MAT9053K Input Power Voltage 220V ±15% Frequency 50/60HZ Rated Input Power Capacity 4.6 KVA No Load Voltage 62V Output Current Range 10 - 200A Rated Output Voltage 18V Duty Cycle 10% 60% Arc Initiation HF Welding Thickness 0.5 - 5.0mm Post Gas 0 - 10 Sec Decline Time 0 - 10 Sec Pre-flow Time 0 - 10 Sec TIG 200P AC/DC Mini. TIG 200P AC/DC - A. TIG 200/315P AC/DC. MIG/MAG Inverter Welders. MIG 160/200 Compact. MIG 200 PFC Compact. MIG 200 Synergic. View or print our welding inverter operator manuals in PDF format. MMA / TIG / MIG / PLASMA. 5 YEAR WARRANTY. Home; Products. MMA/ARC (Stick Tig Welder Settings Made Simplerone stop shop An inverter steps the frequency of the incoming AC power up before it even converts it to DC. That's why the transformer is so small light compared to an old tig welderthe A/C frequency knob allows you to weld with a much higher frequency View or print our welding inverter operator manuals in PDF format. MMA / TIG / MIG / PLASMA. 5 YEAR WARRANTY. The power in inverter technology. Home. Products. Catalogue. About Jasic. TIG 200P AC/DC Mini. TIG 200P AC/DC - A. TIG 200/315P AC/DC. MIG/MAG Inverter Welders. MIG 160/200 Compact MATTIG 200P AC/DC Technical Data MAT9053K Input Power Voltage Frequency Rated Input Power Capacity No Load Voltage Output Current Range Rated Output Voltage Duty Cycle % Arc starting Welding Thickness Post-gas Decline Time Pre-flow Time Remote Control Pulse Frequency 220V ±15% 50/60HZ 4.6 KVA 62V 10 - 200A 18V 60% 0 - 10 Sec 0 - 10 Sec Yes HF View and Download WeldKing TIG 200P AC/DC owner's manual online. TIG 200P AC/DC Welding System pdf manual download. Also for: Stick 200. TIG 200P AC/DC OWNER'S MANUAL . Table of Contents a DC manual (stick) welder, or 3) an AC welder with reduced open-circuit voltage. In most situations, use of a DC, y Porter des lunettes de securite avec ecrans . TIG 200P AC/DC 200 . POWER TIG STICK GUN DC 20 (°) Welding . View and Download Jasic TIG 200 AC/DC Digital Series operator's manual online. AC/DC MMA / TIG Welding machine. TIG 200 AC/DC Digital Series Welding System pdf manual download. Also for: Tig 315 ac/dc digital series, Jt-200d, Jt-315d. i'd go with, ac on, pulse off, pre-flow 1sec, upslope 2.5sec ish if you don't have a pedal, 5mm is gunna need a lot of power say 200amps, down slope 5sec again if you don't have a pedal, post-gas 10sec, ac balance 70-80% (if it's very clean 80%) ac frequency 100hz ish if you have controle over this. Because Nexus does not have much information online in their product manuals, here's what I suggest starting off with however your machine can do it for 1/4" aluminum plate: Set to AC (duh) with high frequency stabilization turned on (duh) Use a 3/16" 25 thoriated tungsten at 240-320 amps; Set the balance control to a mostly DCEN cycle. 70% to Aluminum welding Gas control before and after welding, cleaning of alumina oxide using an AC wave for quality aluminum welding, various adjustments for gas flow time. May work with aluminum from 0.3 mm to 3 mm wall thickness. May work with direct current - DC, for steels and stainless steel from 0.3 mm to a 4 mm material thickness. Aluminum welding Gas control before and after welding, cleaning of alumina oxide using an AC wave for qual